Table of Contents
- Start with what the shell has to do
- When the zip is the last thing specced
- Why the ribbing gets ignored
- Spray rating against rain penetration
- The page a second factory would need
- A last decision, and two longer reads
Turn a bomber sample inside out and look at where the lining meets the zip tape. A folded edge caught under that tape pulls the panel out of square, and you will not see it on a flat lay; it shows up on the rail, when one sleeve hangs lower and the ribbing has already been cut to length. A custom bomber jacket is briefed as a colour and logo job more often than it should be. Then the shell and the zip disagree.
Start with what the shell has to do
Nylon and polyester can arrive at the same weight and still behave nothing alike. Drag a thumbnail across the coated face of one and watch for a pale crease that does not rub out; that mark will reappear at the elbow after a week on a hanger, and no steam will convince it to leave. Hold the sleeve at arm’s length under the storeroom strip light. A high-gloss coating flashes white in a photograph, while a duller finish keeps the weave visible, which is usually what a boutique buyer wants to see when they pick the garment up. I would take the duller finish for a first range, because a shiny shell reads as plastic under store lighting and shoppers read that as cheap.
State weight as a number. State the finish too. Ask whether the coating was applied before or after dyeing, since the order changes how a pale shade sits at a folded cuff. If the range includes a light colour that will spend a season in a sunny window, ask how the dye was checked for fading: AATCC TM16-3:2020 is the published xenon-arc method for colourfastness to light, and it counts exposure in AATCC Fading Units. A shade approved with no exposure figure behind it is a shade nobody can argue about later.
Ask about the roll, too. Two rolls of the same weave can sit a full shade apart, and the difference shows up where a ribbed cuff meets the body panel.
When the zip is the last thing specced
If the front zip is chosen after the shell is approved, expect the tape colour to be picked from a card and the pull to be picked from a catalogue, with nobody writing down either a strength figure or a finish. If the slider lock gives way at the bottom stop, the whole front opens and the garment is finished as far as the customer is concerned. Run the zip up and down a dozen times and feel for a hitch; tug the pull sideways and see whether the slider twists in its seat. Two moves, under a minute. More useful than reading the sheet again.
ASTM D2061, the published Standard Test Methods for Strength Tests for Zippers, opens by saying that no single test decides whether a zip suits a particular end use, and that several may be needed together; the methods it lists cover holding strength of stops and slider locks, chain and element strength, and resistance to the slider pull being torn off. Put the method number in the trim list. Without it, a strength figure is just a number that nobody can reproduce when a batch gets questioned months later.
Why the ribbing gets ignored
Ribbing is ordered by width and colour, almost never by recovery. That is a mistake, because the cuff is the one part a customer touches every time they put the jacket on.
- Fold a cuff twice, hold it for a slow count, then let go and watch how long the rib takes to flatten again.
- If the knit snaps back at once, the elastane is doing its job; if it stays creased, the cuff will bag at the wrist after a few wears.
- A rib that feels dense on a small card often relaxes once it is sewn to a heavier shell.
Stretch the hem band and hold it against the light. You can see the elastane flash between the courses when the knit is under tension, and a band that shows almost none of it will not hold a bloused shape for long. Approve cuff, hem and collar as one decision, from one roll.
Spray rating against rain penetration
These two claims get folded into one word on a hangtag, and they are not the same measurement. AATCC TM22-2024, Water Repellency: Spray Test, is technically equivalent to ISO 4920 and grades how a fabric surface resists wetting by a spray; the specimen is 180 mm square, roughly 7 inches a side, the apparatus is calibrated with 250 mL of distilled water so the spray runs for 25 to 30 seconds, and the result is read as a rating from a chart. The method says plainly that it cannot predict resistance to rain penetration. For that, AATCC TM35 backs the specimen with a weighed blotter, sprays it for 5 minutes under controlled conditions, then reweighs the blotter to find how much water came through. One grades how the surface beads. The other weighs what got through.
A shell can pass a spray rating and still wet through at the shoulders, where a seam and a zip sit close together, and those are two different complaints from the person wearing it. Specify which method you are asking for. Ask too whether the finish was checked after a wash, because a finish that beads on day one and stops beading after three washes is a finish with a short life.
The page a second factory would need
Write down the shell weight in gsm, the weave, the coating and which side it sits on, the zip with its method number, the rib composition, the lining, and the graded measurements with a note on whether they were taken before or after washing. State the approved wash and dry procedure as well, since a coated shell with a ribbed hem will relax differently from a plain woven jacket. A sheet that leaves any of these to memory is a sheet that will be reinterpreted by whoever handles the next batch.
What happens when the person who approved the cuff is no longer on the account? That is the test. Rub a finger along the hem where the lining is anchored and feel for a ridge of trapped thread; check the armhole seam with the sleeve pulled forward; lay the jacket flat and see whether the two sleeves finish at the same point. A custom bomber jacket program lives or dies on this page, not on the artwork file. Ten minutes at the table.
FAQ
Q1: What should a custom bomber jacket tech pack state first?
For a custom bomber jacket, the shell comes first, as a weight in gsm plus weave and coating, then the zip and the rib. Colour comes after those three, because a shade approved on the wrong roll is a shade you cannot reproduce.
Q2: Is a water-repellent finish the same as a rain-resistant one?
No. One grades surface beading, the other measures water that passes through the cloth.
Q3: Can the shell be approved from a photograph?
You can approve a colour that way, with a physical card beside the screen. You cannot approve a finish, a handfeel or a coating crease from an image.
Q4: Which zip test should be written into the trim list?
Ask for the method by name alongside the pull figure. ASTM D2061 collects several zipper strength tests, and one number on its own does not describe how the front will hold up.
A last decision, and two longer reads
Approve the zip method and the rib recovery before anyone argues about the shade. Once those two are in writing, the rest of the sampling round stops wandering. The same discipline carries across a windbreaker, a work jacket and a padded puffer, even though the three silhouettes share very little. The standard numbers and ratings quoted above are published test methods, not readings from one mill, so use them as questions to put to a supplier. For how these layers behave on a body, the Utility Style Guide spends time on workwear shapes, while the Winter Workout Clothes Guide looks at what sits under a shell. One Hundred Pieces takes a longer view of the brand.
