Table of Contents
- The handfeel question comes first
- Necklines change the whole range
- Why colour behaves badly on fleece
- Decoration on a soft surface
- Sizing, wash and the second batch
- Before you commit, and related guides
Most custom pullover complaints begin before anyone chose a fabric. Someone picked a silhouette from a photograph, then went looking for a cloth that would hold it. Fleece does not work that way. A brushed surface has a nap, the nap has a direction, and both change how the garment reads under store lighting. Get the cloth in your hands first. The rest is negotiable.
The handfeel question comes first
Sherpa is plush, high-pile and forgiving of seams. That is precisely why it hides bad ones. French terry is flatter and cooler, and shows every stitch. A cotton-rich brushed fleece sits between them and is usually the safest bet for a first range, if only because it behaves predictably when you wash it. None of that shows up in a flat product shot.
Run your hand across the swatch with the nap, then against it. On a brushed face you will feel the difference immediately. That difference decides whether two panels cut from the same roll look like the same colour once they are sewn together. Mills usually brush the face and the back differently, so ask about both. Ask too whether the two sides were raised on the same pass, because a difference in how each side was brushed will show up as a faint shade change across a seam once the panels are sewn together and the garment hangs under a warm bulb. Small question. Big consequences.
Then ask the awkward one. How much will this relax after a wash? Fleece lofts, then settles. If the sample was cut and measured before washing, your graded chart describes a garment that no longer exists.
Necklines change the whole range
A quarter zip, a half zip and a crew neck can share a body panel and still sell to completely different customers. Opening depth does most of the work. A short zip reads clean and sits happily under a coat. A deeper one turns the piece sportier and gives you somewhere to put a contrast trim.
- Stand collars need enough body to stay up after washing, so ask to see one that has been through a cycle. A fresh sample will flatter you.
- Stretch a ribbed cuff and let go. If it stays stretched on the rail, it will look tired by week two.
- Approve the zip tape and the ribbing in the same round, or expect a mismatch.
One more thing, and it is easy to miss: try the neckline over a tee and under a jacket. A pullover is a layering piece. A collar that looks right on a flat lay can bunch badly once something sits on top of it.
Why colour behaves badly on fleece
A nap catches light. That is why a warm neutral can look almost beige in daylight and decidedly brown under a warm bulb, while the same dye on a woven cloth barely shifts at all. Mocha Mousse flatters brushed fabric for exactly this reason. Future Dusk and Horizon Green give you contrast without dragging the range away from a neutral story. Approve colour on the finished garment, in the light your customers will see it in. A flat swatch tells you the dye. It cannot tell you the garment.
Zips, cords and ribbing are the usual culprits. They are different materials and they take dye differently. Put them on the table together, under the same bulb, at the same time. Approving them separately almost guarantees a mismatch. Hold two core neutrals and one accent. A wider palette on a first order tends to create shade-band arguments later.
Decoration on a soft surface
Fine embroidery and high-pile fleece are a bad combination. The stitches sink, small lettering closes up, and the artwork you approved on a smooth knit simply is not there. Simplify the mark before it is digitised, or choose a woven label instead. A stabiliser behind the stitch and a topping over it will keep the surface flat. Most decent decoration houses suggest this unprompted. If yours does not, ask why.
Patches want clearance from the zip tape and pocket seams, where layers of cloth already stack up. Chenille reads beautifully on a heavier fleece and looks out of place on a light French terry. That is a judgement call, so make it deliberately. Changing it after the samples are cut means starting again.
Sizing, wash and the second batch
Ask for the smallest and largest sizes from the same size set, and measure them before and after a wash. Shoulder drop, body length and sleeve width are the three that drift. Record the tolerance in the tech pack with a note on whether it applies pre-wash or post-wash. That one line will save you an email thread nobody wants to have.
- Store the sealed reference garment with its approved fabric clipping. They belong together.
- When a new batch arrives, measure it before you look at the photos. Numbers first, impressions second.
Re-orders are where a pullover range either proves itself or quietly unravels. If the second batch feels different and nobody can say why, the spec was not specific enough. It is rarely the factory.
FAQ
Q1: What is a custom pullover in practical terms?
A pull-on top made to your own specification of fabric, silhouette, colour, trims and decoration. The written spec is what makes a re-order comparable to the first batch.
Q2: Pullover, hoodie, cardigan: what is the actual difference?
A pullover has no full front opening. A cardigan opens completely. A hoodie adds a hood. The distinction matters most for layering and for where a logo can sit.
Q3: What belongs in the tech pack?
Fabric composition and weight, a graded measurement chart, neckline and trim details, decoration placement, colour references, packing instructions.
Q4: Why did our embroidery disappear?
Almost certainly a high-pile fleece with a fine fill. Small lettering closes up on a lofty surface, so simplify the artwork or switch to a woven label.
Q5: Does a sherpa pullover need a different tech pack?
Same structure, extra lines. Add pile height, edge finishing around the zip and cuff, and how the face is brushed. Those do not exist on a French terry spec.
Q6: Which fleece weight should a boutique start with?
A lighter brushed fleece for trans-seasonal layering, a heavier sherpa for a cold-weather statement piece. Ask for both worn and photographed before you commit. The difference is far clearer on a body than it is folded on a table.
Before you commit, and related guides
Choose the cloth, wash one, then decide the silhouette. Boring sequence. It works. If the sample feels right but nobody can explain why in writing, you are not ready to place the range. That holds for a fleece pullover, a quarter zip pullover, a crewneck sweatshirt and relaxed loungewear alike, because handfeel does as much work as the cut in all of them.
Two related guides on layering and fabric behaviour: Winter Workout Clothes Guide and Utility Style Guide: How to Wear Workwear-Inspired Outfits. For the longer story behind the brand, One Hundred Pieces.
